Handbook of Heat Transfer


Book Description




Thermal Design of Heat Exchangers: A Numerical Approach


Book Description

This book is unique in adopting a numerical approach to the thermal design of heat exchangers. The computation of mean temperature difference, with accommodation of longitudinal conduction effects, makes full optimisation of the exchanger core possible. Sets of three partial differential equations for both contra-flow and cross-flow are established, and form the bases from which a range of methods of direct-sizing and stepwise rating may proceed. Optimisation of an exchanger for steady-state operation is achieved by an approach which allows maximum utilisation of the allowable pressure losses. Transient methods are covered, including the Method of Characteristics, and the Single-Blow method of testing is treated. Numerous aspects of low and high temperature design are discussed, and extensive references to the literature are provided. Schematic algorithms are listed to allow students and practitioners to construct their own solutions, and spline-fitting of data is discussed.




Fouling of Heat Exchangers


Book Description

This unique and comprehensive text considers all aspects of heat exchanger fouling from the basic science of how surfaces become fouled to very practical ways of mitigating the problem and from mathematical modelling of different fouling mechanisms to practical methods of heat exchanger cleaning. The problems that restrict the efficient operation of equipment are described and the costs, some of them hidden costs, that are associated with the fouling of heat exchangers are discussed. Some simple concepts and models of the fouling processes are presented as part of the introduction to the subject.Advice on the selection, design, installation and commissioning of heat exchangers to minimise fouling is given. A large part of the text is devoted to the use of chemical and other additives to reduce or eliminate the problem of fouling. Another large section is designed to give information on both on-line and off-line cleaning of heat exchangers. One of the difficulties faced by designers and operators of heat exchangers is anticipating the likely extent of fouling problems to be encountered with different flow streams. Another large section addresses the question and describes methods that have been used in attempting to define fouling potential. The book concludes with a chapter on how fouling information can be obtained using plant data, field tests and laboratory studies.




Fouling Science and Technology


Book Description

The fouling of heat exchangers, reactors and catalysts remains one of the most urgent problems facing the process industries. Over the past ten years there has been limited research and investigation into the underlying mechanisms which give rise to this problem. For convenience, particularly in heat exchanger technology, the mechanisms involved have been subdivided into different subject areas. It is often the situation that individuals or groups of workers have concentra ted efforts in one or two of these specialist areas and there is a need to integrate the ideas across the whole spectrum of the subject. In addition, topics such as adhesion and surface phenomena have not been properly taken into account up till now in the assessment of the fouling processes. For this reason it was considered essential that the recognised experts from around the world, who are actively concerned with research, development and design in the fieId, should meet and exchange ideas and experience. Such a meeting was held at Alvor, Portugal, in May 1987, sponsored by the NATO Advanced St~dy Institutes Programme. In order to obtain a common basis for the work of the Advanced Study Institute, the whole technological field was reviewed right from the basic concepts to the frontiers of present knowledge. Each invited contributor was asked to make an overall presentation covering his or her area of expertise.




Direct-Contact Heat Transfer


Book Description

to increase the use of direct contact processes, the National Science Foundation sup ported a workshop on direct contact heat transfer at the Solar Energy Research Insti tute in the summer of 1985. We served as organizers for this workshop, which em phasized an area of thermal engineering that, in our opinion, has great promise for the future, but has not yet reached the point of wide-spread commercial application. Hence, a summary of the state of knowledge at this point is timely. The workshop had a dual objective: 1. To summarize the current state of knowledge in such a form that industrial practi tioners can make use of the available information. 2. To indicate the research and development needed to advance the state-of-the-art, indicating not only what kind of research is needed, but also the industrial poten tial that could be realized if the information to be obtained through the proposed research activities were available.




Pharmaceutical Manufacturing Handbook


Book Description

This handbook features contributions from a team of expert authors representing the many disciplines within science, engineering, and technology that are involved in pharmaceutical manufacturing. They provide the information and tools you need to design, implement, operate, and troubleshoot a pharmaceutical manufacturing system. The editor, with more than thirty years' experience working with pharmaceutical and biotechnology companies, carefully reviewed all the chapters to ensure that each one is thorough, accurate, and clear.




Alternatives for Managing the Nation's Complex Contaminated Groundwater Sites


Book Description

Across the United States, thousands of hazardous waste sites are contaminated with chemicals that prevent the underlying groundwater from meeting drinking water standards. These include Superfund sites and other facilities that handle and dispose of hazardous waste, active and inactive dry cleaners, and leaking underground storage tanks; many are at federal facilities such as military installations. While many sites have been closed over the past 30 years through cleanup programs run by the U.S. Department of Defense, the U.S. EPA, and other state and federal agencies, the remaining caseload is much more difficult to address because the nature of the contamination and subsurface conditions make it difficult to achieve drinking water standards in the affected groundwater. Alternatives for Managing the Nation's Complex Contaminated Groundwater Sites estimates that at least 126,000 sites across the U.S. still have contaminated groundwater, and their closure is expected to cost at least $110 billion to $127 billion. About 10 percent of these sites are considered "complex," meaning restoration is unlikely to be achieved in the next 50 to 100 years due to technological limitations. At sites where contaminant concentrations have plateaued at levels above cleanup goals despite active efforts, the report recommends evaluating whether the sites should transition to long-term management, where risks would be monitored and harmful exposures prevented, but at reduced costs.