Mixed-Mode Simulation and Analog Multilevel Simulation


Book Description

Mixed-Mode Simulation and Analog Multilevel Simulation addresses the problems of simulating entire mixed analog/digital systems in the time-domain. A complete hierarchy of modeling and simulation methods for analog and digital circuits is described. Mixed-Mode Simulation and Analog Multilevel Simulation also provides a chronology of the research in the field of mixed-mode simulation and analog multilevel simulation over the last ten to fifteen years. In addition, it provides enough information to the reader so that a prototype mixed-mode simulator could be developed using the algorithms in this book. Mixed-Mode Simulation and Analog Multilevel Simulation can also be used as documentation for the SPLICE family of mixed-mode programs as they are based on the algorithms and techniques described in this book.




Simulation and Optimization of Digital Circuits


Book Description

This book describes new, fuzzy logic-based mathematical apparatus, which enable readers to work with continuous variables, while implementing whole circuit simulations with speed, similar to gate-level simulators and accuracy, similar to circuit-level simulators. The author demonstrates newly developed principles of digital integrated circuit simulation and optimization that take into consideration various external and internal destabilizing factors, influencing the operation of digital ICs. The discussion includes factors including radiation, ambient temperature, electromagnetic fields, and climatic conditions, as well as non-ideality of interconnects and power rails.




Mixed-Mode Simulation


Book Description

Our purpose in writing this book was two-fold. First, we wanted to compile a chronology of the research in the field of mixed-mode simulation over the last ten to fifteen years. A substantial amount of work was done during this period of time but most of it was published in archival form in Masters theses and Ph. D. dissertations. Since the interest in mixed-mode simulation is growing, and a thorough review of the state-of-the-art in the area was not readily available, we thought it appropriate to publish the information in the form of a book. Secondly, we wanted to provide enough information to the reader so that a proto type mixed-mode simulator could be developed using the algorithms in this book. The SPLICE family of programs is based on the algorithms and techniques described in this book and so it can also serve as docu mentation for these programs. ACKNOWLEDGEMENTS The authors would like to dedicate this book to Prof. D. O. Peder son for inspiring this research work and for providing many years of support and encouragement The authors enjoyed many fruitful discus sions and collaborations with Jim Kleckner, Young Kim, Alberto Sangiovanni-Vincentelli, and Jacob White, and we thank them for their contributions. We also thank the countless others who participated in the research work and read early versions of this book. Lillian Beck provided many useful suggestions to improve the manuscript. Yun cheng Ju did the artwork for the illustrations.




Computer-Aided Design of Analog Integrated Circuits and Systems


Book Description

The tools and techniques you need to break the analog design bottleneck! Ten years ago, analog seemed to be a dead-end technology. Today, System-on-Chip (SoC) designs are increasingly mixed-signal designs. With the advent of application-specific integrated circuits (ASIC) technologies that can integrate both analog and digital functions on a single chip, analog has become more crucial than ever to the design process. Today, designers are moving beyond hand-crafted, one-transistor-at-a-time methods. They are using new circuit and physical synthesis tools to design practical analog circuits; new modeling and analysis tools to allow rapid exploration of system level alternatives; and new simulation tools to provide accurate answers for analog circuit behaviors and interactions that were considered impossible to handle only a few years ago. To give circuit designers and CAD professionals a better understanding of the history and the current state of the art in the field, this volume collects in one place the essential set of analog CAD papers that form the foundation of today's new analog design automation tools. Areas covered are: * Analog synthesis * Symbolic analysis * Analog layout * Analog modeling and analysis * Specialized analog simulation * Circuit centering and yield optimization * Circuit testing Computer-Aided Design of Analog Integrated Circuits and Systems is the cutting-edge reference that will be an invaluable resource for every semiconductor circuit designer and CAD professional who hopes to break the analog design bottleneck.




Digital Timing Macromodeling for VLSI Design Verification


Book Description

Digital Timing Macromodeling for VLSI Design Verification first of all provides an extensive history of the development of simulation techniques. It presents detailed discussion of the various techniques implemented in circuit, timing, fast-timing, switch-level timing, switch-level, and gate-level simulation. It also discusses mixed-mode simulation and interconnection analysis methods. The review in Chapter 2 gives an understanding of the advantages and disadvantages of the many techniques applied in modern digital macromodels. The book also presents a wide variety of techniques for performing nonlinear macromodeling of digital MOS subcircuits which address a large number of shortcomings in existing digital MOS macromodels. Specifically, the techniques address the device model detail, transistor coupling capacitance, effective channel length modulation, series transistor reduction, effective transconductance, input terminal dependence, gate parasitic capacitance, the body effect, the impact of parasitic RC-interconnects, and the effect of transmission gates. The techniques address major sources of errors in existing macromodeling techniques, which must be addressed if macromodeling is to be accepted in commercial CAD tools by chip designers. The techniques presented in Chapters 4-6 can be implemented in other macromodels, and are demonstrated using the macromodel presented in Chapter 3. The new techniques are validated over an extremely wide range of operating conditions: much wider than has been presented for previous macromodels, thus demonstrating the wide range of applicability of these techniques.




Simulation Techniques and Solutions for Mixed-Signal Coupling in Integrated Circuits


Book Description

The goal of putting `systems on a chip' has been a difficult challenge that is only recently being met. Since the world is `analog', putting systems on a chip requires putting analog interfaces on the same chip as digital processing functions. Since some processing functions are accomplished more efficiently in analog circuitry, chips with a large amount of analog and digital circuitry are being designed. Whether a small amount of analog circuitry is combined with varying amounts of digital circuitry or the other way around, the problem encountered in marrying analog and digital circuitry are the same but with different scope. Some of the most prevalent problems are chip/package capacitive and inductive coupling, ringing on the RLC tuned circuits that form the chip/package power supply rails and off-chip drivers and receivers, coupling between circuits through the chip substrate bulk, and radiated emissions from the chip/package interconnects. To aggravate the problems of designers who have to deal with the complexity of mixed-signal coupling there is a lack of verification techniques to simulate the problem. In addition to considering RLC models for the various chip/package/board level parasitics, mixed-signal circuit designers must also model coupling through the common substrate when simulating ICs to obtain an accurate estimate of coupled noise in their designs. Unfortunately, accurate simulation of substrate coupling has only recently begun to receive attention, and techniques for the same are not widely known. Simulation Techniques and Solutions for Mixed-Signal Coupling in Integrated Circuits addresses two major issues of the mixed-signal coupling problem -- how to simulate it and how to overcome it. It identifies some of the problems that will be encountered, gives examples of actual hardware experiences, offers simulation techniques, and suggests possible solutions. Readers of this book should come away with a clear directive to simulate their design for interactions prior to building the design, versus a `build it and see' mentality.




Test and Design-for-Testability in Mixed-Signal Integrated Circuits


Book Description

Test and Design-for-Testability in Mixed-Signal Integrated Circuits deals with test and design for test of analog and mixed-signal integrated circuits. Especially in System-on-Chip (SoC), where different technologies are intertwined (analog, digital, sensors, RF); test is becoming a true bottleneck of present and future IC projects. Linking design and test in these heterogeneous systems will have a tremendous impact in terms of test time, cost and proficiency. Although it is recognized as a key issue for developing complex ICs, there is still a lack of structured references presenting the major topics in this area. The aim of this book is to present basic concepts and new ideas in a manner understandable for both professionals and students. Since this is an active research field, a comprehensive state-of-the-art overview is very valuable, introducing the main problems as well as the ways of solution that seem promising, emphasizing their basis, strengths and weaknesses. In essence, several topics are presented in detail. First of all, techniques for the efficient use of DSP-based test and CAD test tools. Standardization is another topic considered in the book, with focus on the IEEE 1149.4. Also addressed in depth is the connecting design and test by means of using high-level (behavioural) description techniques, specific examples are given. Another issue is related to test techniques for well-defined classes of integrated blocks, like data converters and phase-locked-loops. Besides these specification-driven testing techniques, fault-driven approaches are described as they offer potential solutions which are more similar to digital test methods. Finally, in Design-for-Testability and Built-In-Self-Test, two other concepts that were taken from digital design, are introduced in an analog context and illustrated for the case of integrated filters. In summary, the purpose of this book is to provide a glimpse on recent research results in the area of testing mixed-signal integrated circuits, specifically in the topics mentioned above. Much of the work reported herein has been performed within cooperative European Research Projects, in which the authors of the different chapters have actively collaborated. It is a representative snapshot of the current state-of-the-art in this emergent field.




Mechatronic Systems


Book Description

Covers the modelling and simulation of mechatronic and micromechatronic systems using HDLs. Provides an overview of the design of digital and analog circuitry and software for mechatronic systems. Presents practical guidance on both chip and systems design for a wide range of mechatronic applications. Focuses on a practical approach to the design and simulation of electronic hardware and components of mechatronic systems.




Analog Circuit Design


Book Description

Johan H. Huijsing This book contains 18 tutorial papers concentrated on 3 topics, each topic being covered by 6 papers. The topics are: Low-Noise, Low-Power, Low-Voltage Mixed-Mode Design with CAD Tools Voltage, Current, and Time References The papers of this book were written by top experts in the field, currently working at leading European and American universities and companies. These papers are the reviewed versions of the papers presented at the Workshop on Advances in Analog Circuit Design. which was held in Villach, Austria, 26-28 April 1995. The chairman of the Workshop was Dr. Franz Dielacher from Siemens, Austria. The program committee existed of Johan H. Huijsing from the Delft University of Technology, Prof.Willy Sansen from the Catholic University of Leuven, and Dr. Rudy 1. van der Plassche from Philips Eindhoven. This book is the fourth of aseries dedicated to the design of analog circuits. The topics which were covered earlier were: Operational Amplifiers Analog to Digital Converters Analog Computer Aided Design Mixed AlD Circuit Design Sensor Interface Circuits Communication Circuits Low-Power, Low-Voltage Integrated Filters Smart Power As the Workshop will be continued year by year, a valuable series of topics will be built up from all the important areas of analog circuit design. I hope that this book will help designers of analog circuits to improve their work and to speed it up.




The Electronic Design Automation Handbook


Book Description

When I attended college we studied vacuum tubes in our junior year. At that time an average radio had ?ve vacuum tubes and better ones even seven. Then transistors appeared in 1960s. A good radio was judged to be one with more thententransistors. Latergoodradioshad15–20transistors and after that everyone stopped counting transistors. Today modern processors runing personal computers have over 10milliontransistorsandmoremillionswillbeaddedevery year. The difference between 20 and 20M is in complexity, methodology and business models. Designs with 20 tr- sistors are easily generated by design engineers without any tools, whilst designs with 20M transistors can not be done by humans in reasonable time without the help of Prof. Dr. Gajski demonstrates the Y-chart automation. This difference in complexity introduced a paradigm shift which required sophisticated methods and tools, and introduced design automation into design practice. By the decomposition of the design process into many tasks and abstraction levels the methodology of designing chips or systems has also evolved. Similarly, the business model has changed from vertical integration, in which one company did all the tasks from product speci?cation to manufacturing, to globally distributed, client server production in which most of the design and manufacturing tasks are outsourced.