Performance of a Nongrouted Thin Bonded PCC Overlay


Book Description

The use of a thin bonded concrete overlay atop an older surface has been widely incorporated for pavement rehabilitation in Iowa since the early 70's. Two test sections were constructed in 1985 on county road T61 on the Monroe-Wapello County line without the use of grout as a bonding agent to determine if adequate bond could be achieved and structural capacity uncompromised. Both test sections have performed well with one section having higher bond strengths, lower roughness values, higher structural capacity, and less debonding at the joints than the other section. Overall, both ungrouted sections have performed well under substantial truck traffic with minimal surface distress. More attention should be given, however, to rectifying apparent debonding at the joints when no grout is used as a bonding agent.




Performance of Nongrouted Thin Bonded P.C.C. Overlays


Book Description

The Iowa road system has approximately 13,000 miles of Portland Cement Concrete Pavements, many of which are reaching the stage where major rehabilitation is required. Age, greater than anticipated traffic, heavier loads and deterioration related to coarse aggregate in the original pavement are some of the reasons that these pavements have reached this level of distress. One method utilized to rehabilitate distressed or underdesigned PCC pavements is the thin bonded Portland Cement Concrete overlay. Since the introduction of thin bonded overlays on highway pavements in 1973, the concrete paving industry has made progress in reducing the construction costs of this rehabilitation technique. With the advent of the shotblast machine, surface preparation costs have decreased from over $4.00 per square yard to most recently $1.42 per square yard. Other construction costs, including placement, grouting and sawing, have also declined. With each project, knowledge and efficiency have improved.







Portland Cement Concrete Resurfacing


Book Description

This synthesis report will be of special interest to pavement designers, materials engineers, and others seeking information on portland cement concrete resurfacings (overlays) placed over both portland and asphalt cement concrete pavements. Information is presented on the various practices in use for the design, material selection, and construction techniques associated with each pavement type. Additional information is provided on resurfacing experience and performance, including an Appendix cataloging more than 700 existing resurfacing projects in North America. Transportation agencies in the United States are continuing to develop pavement management systems which take an objective and structured approach to life-cycle cost analysis requirements for pavement rehabilitation project analysis. This report of the Transportation Research Board also discusses the considerations involved in the selection of technically feasible resurfacing alternatives. Based on the longitudinal experience of 375 resurfacing projects that were cataloged in 1982 and the more than 700 projects identified in 1993, much useful information on the performance characteristics of portland cement concrete resurfacing is presented.




Portland Cement Concrete Overlays


Book Description

This report presents the latest information on the design, construction and performance of portland cement concrete (PCC) overlays. It describes the four types of PCC overlays that are commonly used in highway pavement applications: bonded PCC overlays, unbonded PCC overlays, conventional whitetopping and ultra-thin whitetopping. Recommended applications, critical design elements, current overlay design methodologies, recommended construction practices, and performance highlights are described for each overlay type. Information is also provided on the selection of PCC overlays as possible rehabilitation alternatives for existing pavements. Taken together, this document addresses the current "state of the technology" of PCC overlays placed on both existing PCC pavements and on existing hot-mix asphalt pavements.




Synthesis of Highway Practice


Book Description







Planning and Research Program


Book Description




Material and Construction Optimization for Prevention of Premature Pavement Distress in PCC Pavements


Book Description

In Phase I, the research team contacted each of 16 participating states to gather information about concrete and concrete material tests. A preliminary suite of tests to ensure long-term pavement performance was developed. The tests were selected to provide useful and easy-to-interpret results that can be performed reasonably and routinely in terms of time, expertise, training, and cost. The tests examine concrete pavement properties in five focal areas critical to the long life and durability of concrete pavements: (1) workability, (2) strength development, (3) air system, (4) permeability, and (5) shrinkage. The tests were relevant at three stages in the concrete paving process: mix design, preconstruction verification, and construction quality control. In Phase II, the research team conducted field testing in each participating state to evaluate the preliminary suite of tests and demonstrate the testing technologies and procedures using local materials.




HRIS Abstracts


Book Description