Essentials of Food Science


Book Description

The fourth edition of this classic text continues to use a multidisciplinary approach to expose the non-major food science student to the physical and chemical composition of foods. Additionally, food preparation and processing, food safety, food chemistry, and food technology applications are discussed in this single source of information. The book begins with an Introduction to Food Components, Quality and Water. Next, it addresses Carbohydrates in Food, Starches, Pectins and Gums. Grains: Cereals, Flour, Rice and Pasta, and Vegetables and Fruits follow. Proteins in Food, Meat, Poultry, Fish, and Dry Beans; Eggs and Egg Products, Milk and Milk Products as well as Fats and Oil Products, Food Emulsions and Foams are covered. Next, Sugar, Sweeteners, and Confections and a chapter on Baked Products Batters and Dough is presented. A new section entitled Aspects of Food Processing covers information on Food Preservation, Food Additives, and Food Packaging. Food Safety and Government Regulation of the Food Supply and Labeling are also discussed in this text. As appropriate, each chapter discusses the nutritive value and safety issues of the highlighted commodity. The USDA My Plate is utilized throughout the chapters. A Conclusion, Glossary and further References as well as Bibliography are included in each chapter. Appendices at the end of the book include a variety of current topics such as Biotechnology, Functional Foods, Nutraceuticals, Phytochemicals, Medical Foods, USDA Choosemyplate.gov, Food Label Health Claims, Research Chefs Association certification, Human Nutrigenomics and New Product Development.




A History of the Old Berks Hunt from 1760 to 1904 - With a Chapter on Early Foxhunting


Book Description

This vintage book contains information on "The Old Berks Hunt", a historical fox hunting club in Oxfordshire, England. With details of its history, notable members, and excursions, this volume will appeal to those with an interest in the history of English Fox hunting, and would make for a worthy addition to collections of related literature. Contents include: "The Early History of Foxhunting", "The Reverend John Loder, 1760 to 1805", "The Rev. Robert Symonds, 1800 to 1807, and 1808 to 1814", "Mr. William Codrington, 1814 to 1824", "Mr. Harvey Combe, 1824 to 1826", "Lord Kintore, Master 1826 to 1830", "The Hon. Henry Moreton, 1830 to 1832", etc. Many vintage books such as this are increasingly scarce and expensive. This volume is being republished now in an affordable, high-quality edition complete with a specially commissioned new introduction on the history of fox hunting.




Tool and Cutter Sharpening


Book Description

Addresses how most sharpening tasks can be carried out using an off hand grinder and a few simply made accessories to a standard comparable to that achieved using much more sophisticated equipment. Intended for model engineers and mechanical crafts, this book is illustrated step-by-step with photographs and technical drawings.




Tool and Cutter Grinding


Book Description

The cutting edges on engineering tools must lie at precise angles to ensure effective cutting, and sharpening must recreate the original geometry of each tool. This book provides an understanding of what is involved in sharpening typical lathe, milling, drilling and threading tools. With over 550 photographs and illustrations this new book covers sharpening techniques for the most commonly used engineering tools, screwdrivers and gravers, lathe, milling, reaming, drilling and threading cutters. It identifies the two principal types of workhead, and discusses the ways in which their geometry affects typical sharpening setups. It teaches how to use the three basic movements of swing, tilt and rotate to position a tool against a grinding wheel to ensure correct tool angles and sharp cutting edges. Contains useful tables for setting cutting and clearance angles and provides general advice on tool and cutter grinders, and includes examples of the use of workholders to suit a range of tools. Includes information on abrasive materials and the types and shapes of grinding wheel suitable for use on a tool and cutter grinder. Finally, it shows photos of accessories that can be made to simplify setups, including workheads, toolholders and fixtures used to hold circular saws, parting tools and dies, as well as an angle gauge to quickly set clearance angles on reamers and milling cutters.







The Shaping Machine


Book Description