› › Test Procedures For Non Sae Hydraulic Hoses

Test Procedures for Non-SAE Hydraulic Hoses

Author : Hydraulic Hose and Hose Fittings Committee

Publisher :

Page : 0 pages

File Size : 39,32 MB

Release : 2001

Category :

ISBN :

Get eBook

Book Description

This SAE Recommended Practice identifies test procedures and parameters which may be used to evaluate, qualify and inspect non-SAE hydraulic hoses or other hose constructions which do not conform to any established ISO or national standards defining hydraulic hoses. (Non-SAE hydraulic hoses are defined as those which do not conform to the categories listed in SAE J517.) It is not intended for evaluating fluoropolymer lined hose constructions or hose constructions with working pressures above 86 MPa.



Optional Test Procedures for Hydraulic Hose Assemblies

Author : Hydraulic Hose and Hose Fittings Committee

Publisher :

Page : 0 pages

File Size : 13,3 MB

Release : 2023

Category :

ISBN :

Get eBook

Book Description

The procedures contained in this SAE Recommended Practice have been developed to establish uniform methods for impulse and high temperature circulation testing of hydraulic hose assemblies under special conditions not specified in SAE J343 for SAE J517 hoses. Basic test procedures shall be in accordance with SAE J343 except as modified in this document. Certain users of SAE standards are requesting that another Optional Test Method V be added to SAE J1405. The primary user base is requesting this modification to SAE J1405 as a function of the U.S. Govt. Paperwork Reduction Act (c. 1995), stating that use of industry standards is preferred over development of other U.S. standards. This was voted upon in the September 2021 meeting with approval to proceed by the committee.



Test and Test Procedures for SAE 100R Series Hydraulic Hose and Hose Assemblies

Author : Hydraulic Hose and Hose Fittings Committee

Publisher :

Page : 0 pages

File Size : 22,82 MB

Release : 2004

Category :

ISBN :

Get eBook

Book Description

This SAE Standard gives methods for testing and evaluating performance of the SAE 100R series of hydraulic hose and hose assemblies (hose and attached end fittings) used in hydraulic fluid power systems. Specific tests and performance criteria for evaluating hose assemblies used in hydraulic service are in accordance with the requirements for hose in the respective specifications of SAE J517. This document further establishes a uniform means of testing and evaluating performance of hydraulic hose assemblies.



Optional Impulse Test Procedures for Hydraulic Hose Assemblies

Author : Hydraulic Hose and Hose Fittings Committee

Publisher :

Page : 0 pages

File Size : 45,26 MB

Release : 2003

Category :

ISBN :

Get eBook

Book Description

The procedures contained in this SAE Recommended Practice have been developed to establish uniform methods for impulse testing of hydraulic hose assemblies under special conditions not specified in SAE J343 for SAE J517 hoses. Basic impulse test parameters are to be in accordance with SAE J343 except as modified in this document.



FLEX-IMPULSE TEST PROCEDURE FOR HYDRAULIC HOSE ASSEMBLIES

Author : Hydraulic Hose and Hose Fittings Committee

Publisher :

Page : 0 pages

File Size : 28,20 MB

Release : 1979

Category :

ISBN :

Get eBook

Book Description

The procedures contained herein have been developed to establish a uniform method for comparative impulse testing of hydraulic hose assemblies with and without flexing in order to determine the effect of flexing on ultimate life of hose. The test method minimizes variables to give a comparison between flexing and non-flexing. Basic impulse test parameters are to be in accordance with SAE J343 except as modified to incorporate flexing. This test is not a requirement for SAE J517 hose.





TESTS AND PROCEDURES FOR SAE 100R SERIES HYDRAULIC HOSE AND HOSE ASSEMBLIES

Author : Hydraulic Hose and Hose Fittings Committee

Publisher :

Page : 0 pages

File Size : 38,37 MB

Release : 1968

Category :

ISBN :

Get eBook

Book Description

This standard is intended to establish uniform methods for the testing and performance evaluation of the SAE 100R Series of hydraulic hose and hose assemblies. The specific tests and performance criteria applicable to each variety of hose and/or assemblies made therefrom are set forth in the respective specifications of SAE J517.



Test and Test Procedures for SAE 100R Series Hydraulic Hose and Hose Assemblies *HS-150/2000*

Author : Hydraulic Hose and Hose Fittings Committee

Publisher :

Page : 0 pages

File Size : 15,63 MB

Release : 1999

Category :

ISBN :

Get eBook

Book Description

This SAE Standard gives methods for testing and evaluating performance of the SAE 100R series of hydraulic hose and hose assemblies (hose and attached end fittings) used in hydraulic fluid power systems. Specific tests and performance criteria for evaluating hose assemblies used in hydraulic service are in accordance with the requirements for hose in the respective specifications of SAE J517. his document further establishes a uniform means of testing and evaluating performance of hydraulic hose assemblies.





Moisture Transmission Test Procedure--Hydraulic Brake Hose Assemblies

Author : Automotive Brake and Steering Hose Standards Comm

Publisher :

Page : 0 pages

File Size : 34,91 MB

Release : 2003

Category :

ISBN :

Get eBook

Book Description

This SAE Recommended Practice is intended for all vehicle hydraulic brake hoses. It is an accelerated test which is intended to provide the user with a method of comparing the ability of hydraulic brake hose designs to retard the ingress of moisture into brake fluid. This document specifies a laboratory performance requirement. ASTM D 1364 Interlaboratory reproducibility and correlation of data have not been defined, nor has correlation been established between field vehicle brake fluid moisture content and data obtained by this document.