The Compatibility of Various Metals and Carbon with Liquid Fluorine
Author : Air Products, Inc
Publisher :
Page : 124 pages
File Size : 30,93 MB
Release : 1960
Category : Carbon
ISBN :
Author : Air Products, Inc
Publisher :
Page : 124 pages
File Size : 30,93 MB
Release : 1960
Category : Carbon
ISBN :
Author : C. J. STERNER
Publisher :
Page : 1 pages
File Size : 20,47 MB
Release : 1961
Category :
ISBN :
Studies were made to determine the compatibility and resistance to corrosion of various metals with liquid Fl at -320F. Metals tested included various alloys of Al, stainless and highstrength steel, Ti, Cu, Monel, Ni, and Mg. It was found that the total corrosion of Ti which had been exposed to liquid Fl was independent of time for perio tamination, Mechanical properties, Handling, Alloys, Metals, *Corrosive liquids, Corrosive gases. Studies were made to determine the compatibility and resistance to corrosion of various metals with liquid Fl at -320F. Metals tested included various alloys of Al, stainless and highstrength steel, Ti, Cu, Monel, Ni, and Mg. It was found that the total corrosion of Ti which had been exposed to liquid Fl was independent of time for periods up to 2 weeks. The corrosion of mg increased up to one day, but longer exposures up to 2 weeks produced no further corrosion. Increased corrosion of metals by Fl contaminated with water does not occur at liquid Fl temperatures, but takes place in the gas phase while the system is warming. Fl which had been liquefied in glass cells was found to contain solid material. Pretreatment with Fl gas is recommended since it can burn off surface contaminationhich might prove dangerous during liquid exposure. Abrading metal surfaces under liquid Fl with wire bristles caused no apparent increase in corrosion rate. (Author).
Author : Harold W. Schmidt
Publisher :
Page : 15 pages
File Size : 26,10 MB
Release : 1958
Category : Charts, diagrams, etc
ISBN :
Specimens of various metals in selected geometric configurations were exposed to liquid fluorine under controlled conditions of flow and pressure. None of the metal samples eroded, decomposed, or exhibited any measurable physical or chemical changes. In a run made with a Teflon sample, instantaneous chemical reaction and decomposition occurred.
Author : Harold W. Schmidt
Publisher :
Page : 292 pages
File Size : 34,29 MB
Release : 1967
Category : Fluorine
ISBN :
Author : Walter K. Boyd
Publisher :
Page : 46 pages
File Size : 49,12 MB
Release : 1965
Category : Liquid propellants
ISBN :
The memorandum summarizes the available information on the compatibility of liquid rocket propellants with prominent materials of construction. Fuels and oxidizers of current interest are discussed. The corrosion data which are presented will apply to storing, handling, and control equipment outside of missiles and to missile components excluding combustion chamber. The compatibility of materials with reaction products in combustion chambers, nozzles, etc., is not considered. Included in the summary are data for many nonmetallic materials. The memorandum is subdivided into sections according to the propellant. Each material of construction is rated for a given medium as belonging to one of four classes, based primarily upon corrosion resistance. Consideration also is given to such factors as catalytic decomposition and sensitivity to impact.
Author : John C. Grigger
Publisher :
Page : 114 pages
File Size : 22,36 MB
Release : 1961
Category : Chemical reactions
ISBN :
Author : United States. Air Force Department
Publisher :
Page : 552 pages
File Size : 17,51 MB
Release : 1962
Category : Materials
ISBN :
Author :
Publisher :
Page : 796 pages
File Size : 29,16 MB
Release : 1989
Category : Alloys
ISBN :
Author :
Publisher :
Page : 368 pages
File Size : 31,45 MB
Release : 1962
Category : Titanium
ISBN :
Author : United States. Wright Air Development Division
Publisher :
Page : 276 pages
File Size : 47,66 MB
Release : 1954
Category : Materials
ISBN :
A review of the research and development work sponsored in the field of materials and processes over the past decade is presented. Abstracts of WADC Technical Reports for the period 1 July 1951 to 30 June 1953 are included. A summary of Technical Reports published in the areas of metallurgy, textiles, petroleum products, structural materials, rubbers, plastics, packaging, protective treatments, analysis and measurements are included also.